2024 Realistic 156-835 Dumps Latest CheckPoint Practice Tests Dumps
156-835 Dumps PDF - 156-835 Real Exam Questions Answers
NEW QUESTION # 32
What kind of cluster Dual-Site can be compared to?
- A. Active-Standby or VSLS
- B. Active-Standby only
- C. VSLS only
- D. Active-Active
Answer: A
Explanation:
A Dual-Site cluster is a type of cluster that combines the features of both Active-Standby and VSLS (Virtual Systems Load Sharing) clusters. Dual-Site clusters allow you to have two active clusters, one at each site, and the traffic is distributed between the two sites based on predefined rules and priorities.
A Dual-Site cluster can be compared to an Active-Standby cluster because one of the clusters is running in a passive mode and is only activated in case of a failure or a planned maintenance of the active cluster. And also can be compared to a VSLS cluster because both clusters are active and share the traffic load.
It's a type of High Availability solution that provides redundancy and failover capabilities across two geographically separated sites. In case of a failure or a outage on one site, the traffic is automatically redirected to the other site, ensuring that the service is not interrupted.
NEW QUESTION # 33
What is the Sync network on Appliances used for?
- A. To synchronize configurations and connections in between connection tables of different Appliances
- B. To transfer data in case of full utilization of the downlink interfaces
- C. May be used for any purpose, but synchronization always have priority
- D. To transfer configuration files from Orchestrators to Appliances
Answer: A
NEW QUESTION # 34
There are two appliances within the same Security Group. One of them is connected by One downlink only, another one by Two downlinks. Assuming there's no NAT and no VPN, what would be proportion of traffic distribution done by Orchestrator?
- A. 100%/0%
- B. 50%/50%
- C. 33%/66%
- D. 66%/33%
Answer: B
NEW QUESTION # 35
What is an uplink interface used for?
- A. To connect in between appliances
- B. To connect Orchestrators to customer's infrastructure
- C. To connect in between Orchestrators
- D. To connect appliances to customer's infrastructure
Answer: D
NEW QUESTION # 36
What does the command'g_all' do?
- A. It's followed by other command and execute it on all active Appliances within Security Group
- B. Bring up all Appliances
- C. It's followed by other command and execute it on all Appliances connected to Orchestrator
- D. Switches all Appliances to Global mode
Answer: A
NEW QUESTION # 37
Which licenses should be issued for the Orchestrator?
- A. The Orchestrator requires NGTX license
- B. Depends on Software Blades enabled on connected appliances
- C. The Orchestrator is considered a Management server, hence it's licensed the same way
- D. No licenses are required for Orchestrator
Answer: D
NEW QUESTION # 38
What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?
- A. Three cables: uplink, downlink, SYNC
- B. Four cables: uplink, downlink, SYNC and Management
- C. Two cables: one uplink and one downlink
- D. One Downlink cable only
Answer: D
NEW QUESTION # 39
What is the max amount of Orchestrators in Dual-site setup?
- A. 2 per Security Group
- B. 0
- C. 4 per Security Group
- D. 1
Answer: B
NEW QUESTION # 40
There's a 23800 appliance with quad NIC in slot 5. What would be the name of port 3 on this NIC?
- A. ethsBP5-03
- B. ethsBP-05
- C. ethsBP3-05
- D. ethBP3-05
Answer: A
NEW QUESTION # 41
For a VSX configuration - Which statement is wrong?
- A. All Virtual Systems exist on all Appliances
- B. VSX configuration is the same on all Appliances within the same Security Group
- C. Each Appliance owns different Virtual Systems
- D. All Virtual Systems exist on the SMO
Answer: A
NEW QUESTION # 42
What is the maximum amount of Appliances within the same Security Group?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 43
There is a Security group of 10 Appliances and all of them are up and running. How many Appliances within a Security Group keep the same connection in its connection table in case of NAT?
- A. 0
- B. All 10
- C. Between 2 and 4
- D. 1
Answer: C
NEW QUESTION # 44
What is the Iterator process?
- A. Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive
- B. Iterator is the process that simulates distribution in case of Appliance failure
- C. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure
- D. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery
Answer: A
Explanation:
Iterator is the process that follows Appliance recovery and simulates what was a distribution if recovered Appliance was alive. The Iterator process runs on the Security Management Server and simulates the distribution of the Security Gateways if the recovered Appliance was alive. This helps ensure that the network remains secure and the traffic flow is optimized.
NEW QUESTION # 45
What does asg monitor command do?
- A. This command does not exist
- B. Show real-time cluster status of Appliances in Security Group
- C. Monitor traffic on Appliances in Security Group
- D. Monitor health status of entire system
Answer: B
NEW QUESTION # 46
What command should be used for collecting diagnostic information about the orchestrator?
- A. cpview
- B. orch_info
- C. cpinfo
- D. asg pert -v
Answer: B
NEW QUESTION # 47
What cannot be learned from the output of asg monitor command?
- A. Port status
- B. Appliances cluster status
- C. Uptime
- D. Security Policy status
Answer: A
NEW QUESTION # 48
How many power supplies are presented on MHO-170?
- A. 0
- B. 1
- C. 2
- D. 1 with option for 2
Answer: C
NEW QUESTION # 49
......
156-835 Premium Exam Engine pdf Download: https://www.exams4collection.com/156-835-latest-braindumps.html
156-835 Exam [2024] Dumps CheckPoint PDF Questions: https://drive.google.com/open?id=1Xe37ssM4kBvevweIatf93Ld0g7IpSLN1
