HPE6-A66 Exam Questions Get Updated [2021] with Correct Answers
Practice HPE6-A66 Questions With Certification guide Q&A from Training Expert Exams4Collection
How to Prepare For Aruba Certified Design Associate Exam
Preparation Guide for Aruba Certified Design Associate Exam
Introduction
This exam validates you have a fundamental knowledge of an Aruba network design and know the Aruba product lines to help you design the network with the assistance of a senior designer. Candidate should know how to read a customer request and extract the information needed for a wired or wireless network. Candidate should know how to use VRF and IRIS. HP HPE6-A66 practice exams and HP HPE6-A66 practice test will help you to understand and memorize the concepts and detailed answers and solutions.
Candidate should give this exam who want:
- To advance your career as a certified professional
- To position yourself as a trusted team member who can contribute to the design of enterprise-wide Aruba campus wired and wireless networks.
- To validate you understand the fundamentals of designing an Aruba Mobile First Platform
Understanding functional and technical aspects of Gather and analyze data, and document customer requirements
The following will be asked from you in the HP HPE6-A66 exam dumps pdf:
- Given an outline of a customer’s needsfor a simple campus environment determine the information required to create a solution
NEW QUESTION 23
A network architect is doing a site survey for a new wireless design One concern the company has with the old wireless network is coverage. In some cases, APs would lose power and some employees in the network would lose wireless connectivity. The new design needs to prevent this issue from occurring. During the site survey, what are best practices to be followed in regards to the dBm signal level and the power of the AP to ensure adequate wireless coverage and minimal overlap of AP signals for the new design?
- A. AP power at 100% and a measurement of -65 dBM on the measuring device
- B. AP power at 75% and a measurement of -80 dBM on the measuring device
- C. AP power at 50% and a measurement of -65 dBM on the measuring device
- D. AP power at 75% and a measurement of -90 dBM on the measuring device
Answer: A
NEW QUESTION 24
A company needs to replace an existing legacy wireless and wired solution with one that supports features like 802 11 ax for APs and logical switching for switches. The company is located on a single floor with two wiring closets. Assume that there will be 10 APs connected via POE+ to each wiring closet, along with 36 wired user connections All switches on a floor should be configured in a single stack. The distance between wiring closets is 100 feet (31 meters).
Which switching solution will minimally provide 10 Gbps uplinks at the most cost-effective price, while still meeting the company's requirements?
- A. 3810M switches
- B. 2930F switches
- C. 5406R switches
- D. 2930M switches
Answer: D
NEW QUESTION 25
A customer currently has sets of three Aruba 5406R switches deployed for an access layer in multiple wiring closets in a building They are clustered in a VSF domain The customer wants to set up Multiple Active Detection (MAD) for the OOBM port, as well as use this port for remote management access. To simplify the connectivity, the customer wants to connect these three switches' OOBM ports to a separate switch in the wiring closet for the OOBM connectivity.
Which would be the most cost-effective solution that would meet the customer's requirements?
- A. 0
- B. 2930M
- C. 2930F
- D. 5406R
Answer: A
NEW QUESTION 26
A network architect is replacing an old wireless implementation based on 802.11 a with a new wireless solution. The company has a lot of money invested in legacy wireless barcode scanners and will not be replacing them. However, the bandwidth that the company expects each AP to have less than 700 Mbps in bandwidth, and this is not expected to change in the future.
Which wireless solution would best meet this company's needs and be the most cost-effective?
- A. 802.11ax
- B. 802.11g
- C. 802.11n
- D. 802.11ac
Answer: A
NEW QUESTION 27
Which IRIS option will automatically create a project with a blank preconfigured Site-1 ?
- A. New Campus
- B. New Site
- C. New Express Mode
- D. New Project
Answer: A
NEW QUESTION 28
When determining a customer's agenda and clarifying their expectations for a new HPE/Aruba deployment, which two questions should be asked during the stakeholder checklist? (Select two.)
- A. Which help desk system is deployed?
- B. What business problems are you trying to solve?
- C. What is your anticipated growth of the environment?
- D. What is the networking experience of onsite personnel?
- E. is a request for proposal or actual bill of materials (BOM) required?
Answer: B,E
NEW QUESTION 29
A company is installing Internet of Things (loT) devices to support a smart and energy-efficient environment for a building, including loT devices for heating and air conditioning, lights, and window shades. loT devices of these types are typically classified as which category of devices?
- A. Highly mobile devices (HMD)
- B. Somewhat mobile devices (SMD)
- C. Stationary devices
- D. Nomadic devices
Answer: D
NEW QUESTION 30
A network architect is designing a Wi-Fi solution for a customer using Aruba Central's VisualRF tool When creating a Campus view, how would the network architect pull in a map that displayed the campus location in a city?
- A. Use VisualRF's built-in map tool and define the appropriate longitude and latitude information
- B. Import the longitude and latitude information from Google Maps
- C. Import the longitude and latitude information from any web-based map site
- D. Create a screen capture from any web-based map site and import the picture file
Answer: C
NEW QUESTION 31
A customer is purchasing Aruba 555 APs for a new wireless network. The APs will be pre-staged as campus APs (CAPs) and be managed by a controller solution During the pre-staging process, console access to the APs might be necessary Which console connection cable should the customer purchase for the 555 APs?
- A. RJ-45
- B. USB-A
- C. RS-232
- D. Micro-B USB
Answer: D
NEW QUESTION 32
A customer has some employees that travel to various locations, where these employees will need Wi-Fi access at these locations. Because many of these locations do not have wireless support, the employees will need to carry an AP solution with them. Internet connectivity, if it doesn't exist at these locations, will be provided by a national phone company USB wireless card which will be connected to AP. The wireless solution needs minimal bandwidth, but needs to minimally support 802.1 lac wave 1 devices.
Which Aruba AP wireless solution would meet the needs of these employees most effectively and cost efficiently?
- A. 303H
- B. 203R
- C. 0
- D. 1
Answer: B
NEW QUESTION 33
A wiring closet with a POE+ switch is 250 feet (76 meters) away from an AP on a building floor. The AP's smart-rate port is connected to a smart-rate port on the switch, which is capable of 10 Gbps. The cable type is Cat5e STP. What is the maximum speed that the customer can expect from the connected AP?
- A. 10 Gbps
- B. 5 Gbps
- C. 2.5 Gbps
- D. 1 Gbps
Answer: C
NEW QUESTION 34
Which component uniquely defines the BSSID when implementing an employee SSID?
- A. Case-sensitive SSID name
- B. Case-insensitive SSID name
- C. Radio MAC address
- D. Wireless device MAC address
Answer: D
NEW QUESTION 35
What is the main key for a network design to ensure users have a good experience running their applications'?
- A. Provision adequate bandwidth.
- B. Determine the number of users per location.
- C. Implement appropriate security controls
- D. Provide appropriate AP density.
Answer: D
NEW QUESTION 36
A company has chosen an Aruba mobility controller solution for the redesign of their wireless network The design will have two 7205 controllers in a cluster for campus employees and a single VMC-50 virtual controller for remote access via a DMZ. A Mobility Master (MM) is used for centralized license and controller management. All controllers will minimally run ArubaOS 8 4 or later Currently the company has 1.000 employees. There are 30 branch offices that will use RAPs to connect to the DMZ controller. A peak of 100 users concurrently using the VIA client will also connect to the DMZ controller.
How many Aruba LIC-VIA licenses does the company need to purchase for this solution?
- A. 0
- B. 1
- C. 1,030
- D. 2
Answer: C
NEW QUESTION 37
A company has two buildings on a campus that are approximately 700 feet (214 meters) apart with a clear line of site. No fiber exists between the buildings; however, there is a need for connecting the networks in the buildings together. The connection between the two buildings will need to support peak rates over 1 Gbps.
Which solution should the company choose that will meet their requirements as well as being cost-effective?
- A. Two outdoor AP 510s
- B. Multi-mode fiber between campus switches
- C. Two outdoor AP 367s
- D. Two outdoor AP 387s
Answer: C
NEW QUESTION 38
Refer to the exhibit.
When planning the use of Cat7 cabling for a SmartRate connection between an ArubaOS AP and an ArubaOS switch, which sections should be considered when calculating distance?
- A. A + B
- B. A + B + C
- C. A + B + C + D
- D. A + C
Answer: C
NEW QUESTION 39
A network architect will be using VisualRF to determine the appropriate wireless coverage for a new wireless design. Seamless, uninterrupted roaming is necessary for this design, since voice will need to be supported. Given these requirements, which information should be used in VisualRF to plan a cost effective solution that meets these requirements?
- A. Minimum -80db, 1 AP per 1,000 square feet, very high-density design
- B. Minimum -70db, 1 AP per 2,500 square feet, capacity design
- C. Minimum -70db. 1 AP per 5,000 square feet, high density design
- D. Minimum -65db, 1 AP per 2,500 square feet, high density design
Answer: D
NEW QUESTION 40
A company has two buildings on a campus, where each building has three floors, which two wiring closets per floor Assume that there will be 24 APs connected via POE+ to each wiring closet, along with 128 wired user connections. Which backplane stacking solution will provide the necessary Ethernet port capacity for all devices on Building 1 Floor 2 and is fully meshed?
- A. Two 381 OM 24-port POE+ switches and three 381OM 48-port switches per wiring closet
- B. Two 2930F 24-port POE+ switches and three 2930F 48-port switches per wiring closet
- C. One 381 OM 24-port POE+ switches and two 2930M 48-port switches per wiring closet
- D. One 2930M 24-port POE+ switch and two 2930M 48-port switches per wiring closet
Answer: D
NEW QUESTION 41
A customer requires a campus core virtualization solution that supports a dual control and management planes, as well as active-active forwarding paths. Which solution would meet the customer's requirements?
- A. VSX
- B. Backplane stacking
- C. VSF
- D. Mesh stacking
Answer: B
NEW QUESTION 42
Which feature does the Aruba AP 387 support?
- A. Indoor usage
- B. included external directional antennas
- C. 60GHZRF
- D. 802.11 ax
Answer: C
NEW QUESTION 43
A network architect is designing a wireless solution for a company that is leasing one floor in a multi-floor building in a downtown area. The customer is concerned about ensuring complete Wi-Fi coverage and pin-pointing RF hazards. What type of survey should the network architect perform?
- A. Spectrum clearing
- B. Virtual
- C. Active
- D. Passive
Answer: C
NEW QUESTION 44
Which must you perform in IRIS to assign a device to a Design Group?
- A. Right-click the device and select Set Layer Membership
- B. Drag and drop the device into the Design Group
- C. Right-click the device and select Set Design Group
- D. Drag and drop the device into the Site
Answer: B
NEW QUESTION 45
......
Prepare Top HP HPE6-A66 Exam Audio Study Guide Practice Questions Edition: https://www.exams4collection.com/HPE6-A66-latest-braindumps.html
Free HP HPE6-A66 Test Practice Test Questions Exam Dumps: https://drive.google.com/open?id=1tjNgTVlbbdp6GNJy-R_E8ubj2gcmOuk5
