Updated Nov 03, 2024 Test Engine to Practice Test for CTS Valid and Updated Dumps
Exam Questions for CTS Updated Versions With Test Engine
NEW QUESTION # 53
What is the standard impedance of a DMX cable?
- A. 55 Q
- B. 110 Q
- C. 75 Q
- D. 150 Q
Answer: B
Explanation:
The standard impedance for a DMX (Digital Multiplex) cable is 110 ohms (). DMX is a standard for digital communication networks commonly used to control stage lighting and effects. The 110-ohm impedance is crucial for ensuring the integrity and reliability of the digital signal over long distances. Using cables with the correct impedance prevents signal reflections and ensures proper transmission of the DMX data without errors, maintaining the synchronization and performance of lighting systems.
NEW QUESTION # 54
Based on this image, what is the aspect ratio for WUXGA?
- A. 1.6:1
- B. 2.35:1
- C. 1.85:1
- D. 1.78:1
Answer: A
Explanation:
WUXGA stands for Wide Ultra Extended Graphics Array and has a resolution of 1920 x 1200 pixels. To determine the aspect ratio, we divide the width by the height:
=1.6:1\text{Aspect Ratio} = \frac{1920}{1200} = 1.6:1Aspect Ratio=12001920=1.6:1 Therefore, the aspect ratio for WUXGA is 1.6:1. This aspect ratio is common for widescreen monitors and provides a wider display format compared to traditional 4:3 screens, enhancing the viewing experience for multimedia content.
NEW QUESTION # 55
The circuit on the RIGHT is an electrical drawing of what type of speaker system?
- A. combination parallel/series circuit
- B. constant voltage
- C. series circuit
- D. stereo pair circuit
Answer: A
Explanation:
The circuit on the right is a combination parallel/series circuit. In this configuration, two sets of speakers are connected in parallel, and these parallel sets are then connected in series. This type of arrangement allows for balancing the load across multiple speakers while maintaining the desired impedance levels.
References:
* Axis Communications - Audio System Design Guidelines
* Electrical Engineering Textbooks
NEW QUESTION # 56
Which of the following is the BEST service when new firmware is available for installed equipment across a fleet of conference rooms?
- A. replacing the equipment
- B. a ringed update approach
- C. updating them all at once
- D. keeping current version
Answer: B
Explanation:
The ringed update approach is the best service when new firmware is available for installed equipment across a fleet of conference rooms. This approach involves updating the firmware in phases or "rings," starting with a small group of devices to ensure that the update is stable and does not introduce new issues. Once the initial ring is confirmed to be successful, the update is gradually rolled out to additional groups, reducing the risk of widespread problems. This method allows for controlled testing and monitoring, ensuring that any issues can be addressed before the update is applied to all devices.
Top of Form
Bottom of Form
NEW QUESTION # 57
As the height of a character increases on a display.
- A. brightness increases.
- B. legibility increases.
- C. legibility decreases.
- D. brightness decreases.
Answer: B
Explanation:
Legibility of text on a display is directly related to the height of the characters. As the height increases, the text becomes easier to read from a distance because the characters are larger and more distinct. This is a fundamental principle in design and ergonomics, ensuring that text is easily readable for users in various viewing conditions. This is particularly important in contexts such as digital signage, user interfaces, and public information displays.References:
* Axis Communications - Display and Readability Guidelines
* Human-Computer Interaction Textbooks
NEW QUESTION # 58
The contrast control sets the
- A. white balance of the Image.
- B. range for the difference between white and black.
- C. color temperature of the image.
- D. range for the hue of the image.
Answer: B
Explanation:
The contrast control on a display adjusts the range for the difference between white and black. Increasing the contrast makes the whites brighter and the blacks darker, enhancing the overall clarity and sharpness of the image. Proper contrast settings are vital for ensuring that the image displayed is visually appealing and easy to interpret, especially in varying lighting conditions.
References:
* Axis Communications - Display Settings and Calibration
* AV Technology Standards
NEW QUESTION # 59
What is a MAIN benefit of an externally managed AV/IT service?
- A. on-demand availability of computer system resources
- B. reduce costs for business-software
- C. cost reduction in operations through clear responsibilities
- D. complete outsourcing of the AV/IT department
Answer: C
NEW QUESTION # 60
What frequency is identified by the numbers above each slider of a graphic equalizer?
- A. highest
- B. secondary
- C. center
- D. lowest
Answer: C
NEW QUESTION # 61
Which viewing category describes the usage of a display as reference for CAD drawings?
- A. ADM (Analytical Decision Making)
- B. FMV (Full Motion Viewing)
- C. BDM (Basic Decision Making)
- D. PV (Passive Viewing)
Answer: A
Explanation:
The viewing category that describes the usage of a display as a reference for CAD drawings is ADM (Analytical Decision Making). This category involves the detailed examination and interpretation of complex information, such as technical drawings or data. Displays used for ADM must have high resolution and clarity to ensure accurate analysis. Axis Technology Specialist documentation categorizes displays for analytical decision-making tasks as requiring superior visual performance to support detailed and precise work.
NEW QUESTION # 62
What key specification of an owner furnished credenza will a technician need to know that may impact the warranty of the AV equipment?
- A. the door hardware and swing operation
- B. the finished pattern, material, and application
- C. the amount of air that moves through the credenza
- D. the quality, size, and availability of cable grommets
Answer: C
Explanation:
The amount of air that moves through the credenza is crucial because AV equipment generates heat during operation. Proper ventilation ensures that the equipment does not overheat, which can cause damage and impact performance. Overheating can void warranties as manufacturers typically specify operational temperature ranges and ventilation requirements. Ensuring adequate airflow is a common stipulation in AV equipment warranties. Proper ventilation helps maintain optimal operating conditions, thereby protecting the equipment and upholding warranty terms.
NEW QUESTION # 63
The BEST way to ensure that a project is on budget is to
- A. calculate the number of calendars days remaining to completion.
- B. ask the installation team to estimate remaining work to completion.
- C. visit the job site and determine the percentage of work completed.
- D. review accrued labor and material costs against remaining work.
Answer: D
Explanation:
The best way to ensure a project is on budget is by continuously reviewing accrued labor and material costs against the remaining work. This approach provides a clear understanding of the financial status of the project and helps in making informed decisions to stay within budget. By tracking these costs and comparing them to the project plan, it is possible to identify any discrepancies early and take corrective actions as needed.
References:
* Axis Communications - Project Management Best Practices
* Project Management Institute (PMI) Standards
NEW QUESTION # 64
What are the dimensions of UHD resolution?
- A. 2048 x 1080 pixels
- B. 2560 x 1440 pixels
- C. 4096 x 2160 pixels
- D. 3840 x 2160 pixels
Answer: D
Explanation:
Ultra High Definition (UHD) resolution is defined as 3840 x 2160 pixels. This resolution is commonly referred to as 4K UHD and provides four times the resolution of Full HD (1920 x 1080 pixels). UHD offers greater detail, clarity, and overall image quality, making it suitable for large displays and high-definition content.
Top of Form
Bottom of Form
NEW QUESTION # 65
When gathering information, it is important to ask about the customer's goals because the
- A. customer may have unrealistic expectations of what can be done.
- B. integrator needs to confirm they understand the relationship between desires and budget
- C. customer may be planning on moving before the project is complete.
- D. integrator needs an understanding of what the customer expects to beable to do with the space.
Answer: D
Explanation:
Understanding the customer's goals is crucial because it helps the integrator design a solution that meets the customer's expectations and functional requirements. Knowing what the customer expects to achieve with the space allows the integrator to tailor the AV system to those needs, ensuring satisfaction and effective use of the system. This understanding also helps in aligning the project scope with the customer's vision and can prevent misunderstandings and misalignments later in the project.
NEW QUESTION # 66
Assuming that the screen and projector are both Ethernet controllable devices, where does the control system for the AV solution need to exist?
- A. in a dedicated rack in the room
- B. connected to the network
- C. in the rear projection room
- D. above the projector, plugged into the serial port on the projector
Answer: B
Explanation:
The control system for the AV solution, assuming both the screen and projector are Ethernet controllable devices, needs to be connected to the network. This allows for centralized control, remote access, and management of the AV devices, ensuring seamless integration and operation. Axis documentation emphasizes the importance of network connectivity for managing Ethernet-enabled AV equipment effectively.
NEW QUESTION # 67
When is the optimal time to conduct training of end users in a new AV installation?
- A. during installation so that the system can be configured and modified in line with the user's knowledge
- B. when all users of the facility can be trained at the same time
- C. at the time of system handover with accompanying user guides
- D. after all participants have reviewed equipment manuals
Answer: C
Explanation:
The optimal time to conduct training of end users in a new AV installation is at the time of system handover with accompanying user guides. This ensures that users receive hands-on training with the actual equipment they will be using, allowing them to understand its operation fully and ask questions while a technician is present. Providing user guides during this time also gives them a reference to consult after the training session.
Axis Technology Specialist documentation stresses the importance of comprehensive training and support at the system handover phase to maximize user proficiency and satisfaction.
NEW QUESTION # 68
What is the FIRST stage in troubleshooting an AV system?
- A. determining which devices are fully functional
- B. identifying the symptoms of the error
- C. evaluating possible sources of error
- D. reviewing the system diagram showing the connections and the signal flow
Answer: B
Explanation:
The first stage in troubleshooting an AV system is identifying the symptoms of the error. This step involves observing and documenting the specific issues or malfunctions that are occurring. By clearly understanding and articulating the symptoms, a technician can more effectively diagnose the problem and narrow down potential causes. Once the symptoms are identified, the technician can proceed to evaluate possible sources of error, check device functionality, and review system diagrams as needed.
NEW QUESTION # 69
Company information, statement of work, drawings, and bill of materials are presented to the customer as what set of documents?
- A. request for proposal
- B. contract documents
- C. request for quote
- D. bid packet (response)
Answer: D
Explanation:
Company information, statement of work, drawings, and bill of materials are presented to the customer as a bid packet (response). This set of documents is used to respond to a request for proposal(RFP) and provides detailed information about how the contractor intends to meet the project requirements. Axis Technology Specialist documentation emphasizes the importance of a comprehensive bid packet to communicate the scope, approach, and cost of a project to the client.
NEW QUESTION # 70
When creating an estimate for a request for proposal (RFP), what is the FIRST tiling that should be done?
- A. create the submittal
- B. obtain the costs
- C. schedule a site visit
- D. read the project description
Answer: D
Explanation:
The first step in creating an estimate for an RFP is to read the project description thoroughly. This ensures that you fully understand the scope, requirements, and objectives of the project. By doing so, you can accurately determine what is needed, identify potential challenges, and make informed decisions on costs, resources, and scheduling. Starting with a clear understanding of the project description sets
NEW QUESTION # 71
To help end users remember key points of the training, the training documentation should include
- A. equipment datasheets.
- B. a customized quick start guide.
- C. instructions for maintaining system input devices.
- D. user manuals for each piece of equipment.
Answer: B
Explanation:
A customized quick start guide is particularly useful for helping end users remember key points of the training.
These guides provide concise, easy-to-follow instructions tailored to the specific system and user needs, highlighting the most important operational steps and features. This helps users quickly familiarize themselves with the system and perform essential tasks without having to refer to extensive manuals. Including visual aids, such as diagrams and screenshots, further enhances the effectiveness of the quick start guide.
NEW QUESTION # 72
Before confirming an anticipated completion date with the customer, it is MOST important to
- A. ensure the date is not a holiday.
- B. create the system maintenance schedule.
- C. double check the floor finishes.
- D. ensure no components are backordered.
Answer: D
Explanation:
Before confirming an anticipated completion date, it is critical to ensure that all components required for the project are available and not backordered. Backordered components can cause significant delays, impacting the overall project timeline. By verifying the availability of all necessary components, you can provide a realistic and reliable completion date to the customer. This step is essential for effective project planning and avoiding unexpected delays.
NEW QUESTION # 73
Which document is used to clarify a project design issue?
- A. request for Information
- B. change order
- C. progress report
- D. request for change
Answer: A
Explanation:
A Request for Information (RFI) is a document used to clarify project design issues. RFIs are typically issued when there is a need for additional information or clarification on specific aspects of the project design. This helps ensure that all parties have a clear understanding of the requirements and can proceed with accurate and consistent implementation. RFIs are commonly used in construction and AV projects to address uncertainties or discrepancies in the design documents.
NEW QUESTION # 74
Which method of control is supported by HDBaseT?
- A. PCIE
- B. RS-232
- C. DMX512
- D. DAU
Answer: B
Explanation:
HDBaseT technology supports the transmission of multiple signals over a single cable, including video, audio, Ethernet, power, and control signals. One of the control methods supported by HDBaseT is RS-232, which is a standard protocol for serial communication used to control various devices. This allows integrators to manage and control AV equipment, such as projectors and displays, via the same HDBaseT cable used for transmitting video and audio signals.
NEW QUESTION # 75
Which one of these features has to be disabled for a network switch in a Dante network?
- A. PoE (Power over Ethernet)
- B. QoS (Quality of Service)
- C. EEE (Energy Efficient Ethernet)
- D. IGMP (Internet Group Management Protocol)
Answer: C
Explanation:
Energy Efficient Ethernet (EEE) must be disabled in a Dante network. EEE can cause latency and jitter issues which are detrimental to audio streams. Dante is designed for low-latency, high-reliability audio networking, and EEE's power-saving mechanisms, which involve putting links to sleep, can interfere with the consistent data transmission required by Dante networks. Disabling EEE ensures stable and uninterrupted network performance for audio applications.
NEW QUESTION # 76 
According to the Gantt chart pictured, the Project Manager should wait to start Activity C until which predecessor has been reached?
- A. Milestone X
- B. Week 4
- C. Week 3
- D. Activity B
Answer: A
Explanation:
In the provided Gantt chart, Activity C is scheduled to start after the completion of Milestone X. This is evident as the milestone symbol (diamond) for Milestone X appears right before the beginning of Activity C, indicating that Activity C is dependent on the completion of Milestone X.
NEW QUESTION # 77
A loud hiss is coming from the audio system. This is MOST LIKELY caused by
- A. the microphones being off.
- B. fluorescent lighting.
- C. poor gain structure.
- D. phase cancellation issues.
Answer: C
Explanation:
A loud hiss in an audio system is most commonly caused by poor gain structure. Gain structure refers to the optimal setting of input and output levels throughout an audio system to minimize noise and distortion while maximizing signal quality. Incorrectly set gain levels can amplify the inherent noise floor of the system, leading to audible hiss. Ensuring proper gain staging at each step-from microphones to mixers to amplifiers-helps reduce this noise.
NEW QUESTION # 78
......
Axis Communications CTS Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
AVIXA CTS Exam Certification Details:
| Non-Member Exam Price | $475(USD) |
| Books / Training | Candidate Handbook |
| MemberExam Price | $375(USD) |
| Sample Questions | AVIXA CTS Sample Questions |
| Duration | 150 mins |
CTS Exam Dumps - Free Demo & 365 Day Updates: https://www.exams4collection.com/CTS-latest-braindumps.html
Pass CTS Exam with Updated CTS Exam Dumps PDF: https://drive.google.com/open?id=1q6X-AuaIgwHfayUPwMiDW9fXbBy_I1kH
