Updated Jan 15, 2022 Certification Exam NACE-CIP2-001 Dumps - Practice Test Questions
Updated Verified NACE-CIP2-001 dumps Q&As - Pass Guarantee or Full Refund
NEW QUESTION 17
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Document the readings at the end of the shift
- C. Advise the coating applicator supervisor of your readings
- D. Call your supervisor
Answer: C
NEW QUESTION 18
Inspector reports should always be copied to:
- A. The Owner only
- B. Whomever the Owner identifies
- C. The Contractor and Owner
- D. All parties involved in the project
Answer: B
NEW QUESTION 19
In which type of concrete are laitance commonly encountered?
- A. Poured (wet cast)
- B. Concrete block (poured with a form)
- C. Glass fiber cement
- D. Gunite
Answer: A
NEW QUESTION 20
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Power Tools
- B. Abrasive Blasting Equipment
- C. Scarifiers
- D. Water Jetting Equipment
Answer: D
NEW QUESTION 21
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Steam cleaning only
Answer: B
NEW QUESTION 22
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. So the contractor has a single document to reference
- C. To supersede the requirements of the product data sheets
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 23
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Wetting stage
- B. Cure stage
- C. Flow stage
- D. Gel stage
Answer: C
NEW QUESTION 24
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Structural integrity
- B. Air changes
- C. a), b), and c)
- D. Lighting
Answer: C
NEW QUESTION 25
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. Cold flow or creep
- B. No difference from any other coating
- C. A very low reading
- D. A very high reading
Answer: A
NEW QUESTION 26
When observing fabrication defects the NACE Inspector should:
- A. Consult the specification to determine how they should be treated
- B. Require they be corrected prior to coating
- C. Stop the job immediately
- D. Write an NCR and call the fabricator
Answer: A
NEW QUESTION 27
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. provide protection against soil chemicals.
Answer: B
NEW QUESTION 28
Coating application to concrete substrates is:
- A. The same as coating steel
- B. Not required as Concrete is inorganic
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION 29
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Ignore the additional requirement
- B. Request clarification from the specifier
- C. Enforce the additional requirement
- D. Call your supervisor
Answer: C
NEW QUESTION 30
The HATE adhesion tester uses
- A. a special tape to apply pressure to the test dolly.
- B. mechanical means only to apply pressure to the test dolly.
- C. a hydraulic piston to apply pressure to the test dolly.
- D. compressed air to apply pressure to the test dolly.
Answer: C
NEW QUESTION 31
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. Low Voltage Sponge Type
- B. High Voltage DC Constant Current
- C. High Voltage AC
- D. High Voltage DC Pulse Type
Answer: B
NEW QUESTION 32
All of these are advantages of using repair patches EXCEPT
- A. special tools or equipment are required.
- B. excellent abrasion resistance.
- C. inert to common acids, alkalis, and solvents.
- D. barrier to moisture and corrosion.
Answer: A
NEW QUESTION 33
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION 34
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. wherever it is convenient
- C. in a well ventilated area separate from the work place.
- D. in a refrigerated warehouses
Answer: C
NEW QUESTION 35
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 2
- C. SP 1 followed by SP 3
- D. SP 1 followed by acid etching
Answer: B
NEW QUESTION 36
......
Exam Engine for NACE-CIP2-001 Exam Free Demo & 365 Day Updates: https://www.exams4collection.com/NACE-CIP2-001-latest-braindumps.html
NACE-CIP2-001 PDF Questions and Testing Engine With 100 Questions: https://drive.google.com/open?id=1EzE0oupYGnTOlgwQObDT8xTvNWVCwflO
